Epson EPL-N7000 Instrukcja Użytkownika

Where to Find InformationSetup Guide (this manual)Provides you with information on assembling the printer and installing the printer software.Online g

6 Assembling the Printer* 800 mm when the optional 4-Bin Mailbox is installed.cCaution:❏ Avoid locations that are subject to direct sunlight, excessiv

Assembling the Printer 7Installing the Imaging CartridgeHandling precautions:❏ When handling the imaging cartridges, always place them on a clean, smo

8 Assembling the Printer3. While holding the imaging cartridge horizontally, gently shake it a few times to distribute the toner evenly.cCaution:❏ Nev

Assembling the Printer 94. Carefully insert the imaging cartridge into the printer, making sure that the pins on both sides of the cartridge are align

10 Assembling the Printer5. Close the front cover by pressing it firmly until it clicks into place.

Readying the Printer for Use 112Readying the Printer for UsePlugging in the PrinterFollow these steps to plug in the printer:1. Make sure the printer

12 Readying the Printer for UseLoading PaperMP trayThe MP tray is the most flexible paper source, accommodating various paper sizes and media types.Fo

Readying the Printer for Use 132. While squeezing the guide lock on the right side of the paper guide, slide the paper guide to accommodate the paper

14 Readying the Printer for Use4. While squeezing the guide lock on the right side of the paper guide, adjust the paper guide to the size of the paper

Readying the Printer for Use 152. Press the Enter button three times. The printer starts printing a status sheet.Note:If the status sheet cannot be

2Online Help for printer softwareClick Help for detailed information and instructions on the printer software that controls your printer. Online help

16 Readying the Printer for UseConnecting the PrinterUSB interface/Parallel interfaceUse a shielded, USB version 1.1 cable or twisted-pair parallel in

Readying the Printer for Use 172. Plug the USB or parallel interface cable into the printer’s USB or parallel connector, as shown below.3. Plug the ot

18 Readying the Printer for UseNetwork interfaceThis printer comes with the network interface connection. After connecting your printer to the network

Readying the Printer for Use 19To set the printer’s IP address using the control panel or the provided utility, see the Network Guide. You must instal

20 Installing the Printer Software3Installing the Printer SoftwareWhen you install the printer software, the following components are installed.❏ Prin

Installing the Printer Software 213. Click Continue. When the software license agreement screen appears, read the statement and then click Agree.4. In

22 Installing Options4Installing OptionsFor information on the specifications of the options and their handling precautions, see the Reference Guide.T

Installing Options 23Before Installing the Hard Disk Drive or Memory ModuleFollow these steps to prepare the printer for the installation of a hard di

24 Installing Options3. Loosen the two screws located on the top-right edge of the printer.4. Remove the two screws located near the bottom-right edge

Installing Options 255. Remove the right cover.6. Identify the Hard Disk Drive connector and the installation slot for the memory module on the circui

Laser Printer®Setup Guide1 Assembling the Printer . . . . . . . . . . . . . . . . . 12 Readying the Printer for Use. . . . . . . . . . . . 113 Insta

26 Installing OptionsHard Disk DriveFollow these steps to install the Hard Disk Drive:Note:There are two cables included with the Hard Disk Drive. Use

Installing Options 273. Connect the other end of the cable to the Hard Disk Drive connector on the circuit board.4. Secure the drive with the screws t

28 Installing OptionsMemory ModuleFollow these steps to install a memory module:1. Perform the procedure described in “Before Installing the Hard Disk

Installing Options 294. Insert one corner of the memory module into the memory slot and push it in until the clip comes up.5. Insert the other corner

30 Installing OptionsReplacing the right coverFollow these steps to replace the printer’s right cover after installing the optional Hard Disk Drive or

Installing Options 312. Fasten the right cover with screws, as shown below.At the bottom of the right coverAt the top of the right coverEnglish

32 Installing Options3. Close the front cover by pressing it firmly until it clicks into place.4. Reconnect all interface cables and the power cord.5.

Installing Options 33Interface CardFollow these steps to install an interface card:1. Make sure the printer is turned off and the power cord and inter

34 Installing Options3. Insert the interface card firmly.4. Secure the interface card with its screws.

To Know More About Your Printer 35To Know More About Your Printer❏ Reference Guide (PDF)This guide provides detailed information about printing from a

iiAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechan

36 To Know More About Your PrinterViewing and printing the Paper Jam GuideFollow these steps to view and print the Paper Jam Guide:1. A Paper Jam Guid

Safety Instructions 37Safety InstructionsLaser Printer Precautions This printer uses laser technology. Follow the precautions below carefully to ensur

38 Safety Instructions❏ Do not attempt to modify or take the imaging cartridge apart. It cannot be refilled.❏ Do not touch the toner and avoid getting

Safety Instructions 39❏ Use the type of power source indicated on the label. If you are not sure of the type of power available, consult your dealer o

40 Safety InstructionsWhen using the printer❏ The printer weighs about 28.0 kg (61.7 lb) without consumable products installed. One person should not

Safety Instructions 41❏ Never push objects of any kind through cabinet slots as they may touch dangerous voltage points or short out parts that could

42 Safety InstructionsThis product’s power cord is for use with this product only. Using it with other equipment may result in fire or electric shock.

Safety Instructions 43Ozone exposure limitThe recommended exposure limit for ozone is 0.1 parts per million (ppm) expressed as an average time-weighte

44 Safety InstructionsSince radiation emitted by the laser is completely confined within protective housings and external covers, the laser beam canno

Safety Instructions 45❏ The blue wire must be connected to the terminal in the plug marked with the letter N.❏ The brown wire must be connected to the

Assembling the Printer 11Assembling the PrinterRemoving the Protective MaterialsFollow these steps to remove the protective materials from the printer

46 Safety Instructions

2 Assembling the Printer2. Pull the paper cassette out until it stops.3. While pressing the gray stoppers located on both sides of the paper cassette,

Assembling the Printer 34. Remove the tapes that secure the cassette cover, and then remove the cover. Follow by removing all the tapes and protective

4 Assembling the Printer7. Remove the protective materials from inside the printer.8. Close the front cover by pressing it firmly until it clicks into

Assembling the Printer 5Finding a Place for the PrinterAllow adequate space for easy operation and maintenance.The illustration shows the recommended