Epson Endeavor Podręcznik Użytkownika Strona 129
- Strona / 197
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
As the program checks each track, it decreases the cylinder
numbers to zero. When the test is complete, the program
displays a report on the status of the disk, such as the following:
Analysis finished.
Count of tracks flagged bad
=
12
Count-of tracks with read, verify errors =
n
Count of good tracks
= nnnn
No
read, verify error was detected.
If the program finds
errors,
the screen displays a table of the
tracks that produced the errors. Then you see this message:
Press ENTER to return to the menu.
Check the information displayed. Then press
[Enter]
to return to
the Hard Disk Format Menu.
Exiting the Program
To leave the Hard Disk Format Menu, select
Exit.
You
see
the
operating system command prompt.
If you formatted the hard disk or ran the Destructive surface
analysis option, you must now prepare your hard disk for use
with your operating system. See your operating system manual
for instructions.
Formatting a Hard Disk
5-11
- User’s Guide 1
- Important Safety Instructions 5
- Contents 9
- VGA Utilities 14
- Optional Equipment 14
- Over Drive Processor 15
- Math Coprocessor 15
- AIternate VGA lnterface 15
- How to Use This Manual 16
- Chapter 1 17
- Turning On the Computer 18
- Using Your Computer 19
- Del to start SETUP 20
- Turning Off the Computer 21
- Using Disks and Disk Drives 21
- How Disks Store Data 22
- Types of Diskette Drives 23
- 1.44MB. 720KB 24
- Write-protecting Diskettes 28
- Formatting Diskettes 33
- Backup Copies 33
- Hard Disk Drive 34
- Backing up the hard disk 35
- Caring for your 35
- Special Keys on the Keyboard 36
- Stopping a Command or Program 37
- Resetting the Computer 38
- Password 39
- Changing the Processor Speed 40
- Chapter 2 44
- How to Use This Chapter 45
- Removing the Cover 47
- Changing the Jumper Settings 49
- Two pin jumpers 50
- Setting the Jumpers 52
- Memory Modules (SIMMs) 54
- Inserting SIMMs 56
- Removing SIMMS 58
- Removing an Option Curd 63
- Replacing the 65
- New Processor Chip 66
- Installing the Memory Chips 67
- Using a Display Adapter 71
- Replacing the Cover 72
- Post-installation Procedures 73
- Chapter 3 74
- Where to Go Next 77
- Removing the Mounting Frames 79
- Installing the Hard Disk 81
- Connecting the Cables 85
- Installing the Drive 93
- Installing and 101
- Chapter 4 110
- Deleting Tests 112
- Adding Tests 113
- Running Tests 114
- Resuming From an Error 115
- Running System Diagnostics 116
- System Diagnostic Tests 116
- System diagnostic tests 116
- Error Messages 117
- Chapter 5 119
- HDFMTALL and press 120
- Formatting a New Disk 121
- Reformatting a Used Disk 121
- Selecting an Option 121
- Selecting a Drive 122
- Formatting a Hard Disk 125
- OF ALL YOUR FILES 126
- Format completed 126
- Current cylinder is nnnn 128
- Exiting the Program 129
- Chapter 6 130
- Setup Guide 132
- Troubleshooting 6-3 132
- 6-4 Troubleshooting 133
- Power-on 134
- (continued) 134
- Troubleshooting 6-5 134
- The Computer Won't Start 135
- The Computer Does Not Respond 136
- 6-8 Troubleshooting 137
- Restoring the Power Supply 138
- Password Problems 139
- Accessing Your System 140
- Keyboard Problems 141
- Monitor Problems 142
- 6-14 Troubleshooting 143
- Diskette Problems 144
- Diskette Drive Problems 146
- Hard Disk Problems 147
- Preparing the Drive 148
- Accessing Data on the Drive 149
- Software Problems 150
- Printer Problems 151
- Option Card Problems 152
- Mouse Problems 153
- Memory Module Problems 154
- Appendix A 155
- Controllers 156
- Specifications A-3 157
- Mass Storage 158
- Keyboard 158
- Physical Characteristics 159
- Power Supply 159
- Environmental Requirements 160
- Power Source Requirements 161
- System Memory Map 162
- GIossary 163
- Cylinders 169
- Data diskette 169
- Extended memory 172
- Extension 172
- Filename 172
- Fixed disk 172
- Graphics 173
- Hard disk 173
- Hardware 173
- Hexadecimal 173
- Multifrequency monitor 178
- Multitasking 178
- Numeric keypad 178
- Operating speed 178
- Operating system 178
- Glossary 19 182
- Glossary 21 184
- Video card 185
- Write-protect 185
- Cnnector 186
- 10 Index 195
- 400195100 197
Powiązane produkty i podręczniki dla Części komputerowe Epson Endeavor
Części komputerowe Epson Endeavor Dokumentacja
(11 strony)
(11 strony)
Części komputerowe Epson QX-10 Dokumentacja
(45 strony)
(45 strony)
Części komputerowe Epson NX Instrukcja Obsługi
(154 strony)
(154 strony)
(148 strony)
Części komputerowe Epson LT-286 Dokumentacja
(15 strony)
(15 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji