Epson C82324* Podręcznik Użytkownika Strona 1

Przeglądaj online lub pobierz Podręcznik Użytkownika dla Networking Epson C82324*. Epson C82324* User`s guide Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj

Podsumowanie treści

Strona 1 - 4001-882

EPSON®4001-882EC2-00

Strona 2 - Card for NetWare

About This ManualThis manual describes how to install, configure, and use yourEthernet Card in a Novell NetWare environment for thefollowing cable con

Strona 3

Terms and ConceptsThe master file server stores data required for the Ethernet Card tooperate as a print server. Each Ethernet Card print server hason

Strona 4 - FCC Compliance Statement

Resetting (or Rebooting) the Ethernet Card causes it to reinitializeand print a new configuration report. You can reset theEthernet Card in three ways

Strona 5 - Contents

Using the Ethernet Card in print server mode provides thehighest printing speed while retaining the control, security andconvenience of a Novell NetWa

Strona 6

All configuration changes are made using PCONSOLE. Thisincludes adding or deleting queues, changing queue priorities, orchanging file server assignmen

Strona 7 - Appendix

After installing the Ethernet Card on the master file server withEPSETUP, you can also use Novell’s PCONSOLE 3.x or 2.15c toperform all configuration

Strona 8 - Ethernet Card Hardware

Chapter 1Installing the Ethernet CardThis chapter explains how to install the Ethernet Interface Cardfor NetWare in your printer. This chapter also sh

Strona 9

The Ethernet Card is installed in the optional interface slot ofyour Epson printer. See your printer’s user’s guide for thelocation of the optional in

Strona 10 - Installation Overview

The serial number is required for software installation. The firstpage of this manual also includes a box for you to fill in the serialnumber. For con

Strona 11 - Terms and Concepts

Attach the network cable to the appropriate connector on theinterface, as shown in the following diagram.Thin coaxialI10BASE-T\0Using the Epson PostSc

Strona 12 - How the Ethernet Card Works

C82324*Ethernet InterfaceCard for NetWare®User’s Guide

Strona 13

Use EPSETUP for your initial Ethernet Card setup. After settingthe Ethernet Card up on at least one file server, you can use eitherEPSETUP or PCONSOLE

Strona 14 - The Ethernet

3.From the network or local drive where you copied the EthernetCard utilities, enter EPSETUP.4.Select “Install New Ethernet Interface Card.”5.Enter th

Strona 15

d. Press INSERT to display a list of file servers. Select a fileserver upon which you have supervisor privilege.(Assigning a queue on a file server ac

Strona 16 - Installing the Ethernet Card

Before Running EPSETUPBefore using EPSETUP to install Ethernet Card as a remoteprinter, you must do the following:1.2.3.4.5.6.Decide which Novell prin

Strona 17 - Serial Number

4.5.6.7.8.9.10.Select “Install New Ethernet Interface Card.”Enter the eight-digit Ethernet Card serial number. The serialnumber is located on the comp

Strona 18 - Setting up the printer

Chapter 2After the Ethernet Card is installed and operating as a printserver, you can change its basic operating parameters usingEPSETUP. You can comp

Strona 19 - Ethernet Card Software Setup

Configuration Using EPSETUP1.Log into the network with supervisor privilege.2.Enter the EPSETUP utility.3.Select “Change Current Print Server Configur

Strona 20 - Before setting up

4.To add a queue to the list, press INSERT. Select the file server thatincludes the queue you would like the Ethernet Card toservice.a.The screen disp

Strona 21 - Press ENTER

3.In the “Printer Configuration” screen, you can complete thefollowing tasks:a.Change printer port name.b.Turn configuration report printing on/off. (

Strona 22 - Remote Printer

Rename Print ServerAlways use EPSETUP (or EPCONFIG) to rename on the masterfile server. Never use PCONSOLE to rename the print server onthe master fil

Strona 23 - Running EPSETUP

All rights reserved. No part of this publication may be reproduced, stored in a retrievalsystem, or transmitted in any form or by any means, mechanica

Strona 24

3.In the “Options” menu, press ESC. Select “Reset.”Caution:Once you select “Reset," you must wait for the “Reset has beencompleted” message to ap

Strona 25 - Chapter 2

clcl00clclAdding or deleting a queue from the Ethernet Card port’sservice listChanging the LPTl port’s name or configuration (this includesturning the

Strona 26 - Configuration Using EPSETUP

Advanced Configuration Using EPCONFIGEPCONFIG is a command-line utility used by the supervisor forconfiguring the Ethernet Cards network communication

Strona 27

Using EPCONFIGTo use EPCONFIG, log in to the network with supervisorprivilege. You must log in to the master file server to successfullycomplete the c

Strona 28 - Change Master File Server

[IA ] (pipe) character means“either/or.” You have a choicebetween two items separated by aI*Brackets indicate that the encloseditem is optional. If no

Strona 29 - Set Password

Reset (Reboot) the Ethernet CardEPCONFIG serial-number N=E RESETThis command resets the specified the Ethernet Card. When inprint server mode, the Eth

Strona 30 - Reset Print Server

You must log into the master file server to rename the print server.Default name: the Ethernet Card’s S-digit serial number.When you rename the print

Strona 31

Turn Configuration Report Off/OnEPCONFIG serial-number N=E RPT=NORP 1 RP Use this command to enable or disable configuration reportprinting.RP enabl

Strona 32 - Advanced

In print server mode, this parameter is optional, unless yournetwork uses a communication standard other than IEEE 802.3 orEthernet II Novell type 813

Strona 33 - Using EPCONFIG

Enter one of the following hexadecimal values for C= ethernet_type:To configure the Ethernet Card for 802.3 only use 0001 through05FF.To configure the

Strona 34 - Show Current Settings

FCC Compliance StatementFor United States UsersThis equipment has been tested and found to comply with the limits for a Class A digitaldevice, pursuan

Strona 35 - Print Server

Chapter 3TroubleshootingThis chapter is divided into the following sections:clClclLights--describes the Ethernet Card indicator light behavior,includi

Strona 36 - Set Pass word

Here is a brief explanation of indicator light activity1Green1 Red 1FunctionI.I,0.I,0000Starting power-on testsTestingLooking for master file serverCo

Strona 37 - Set the Ethernet Network Type

TroubleshootingInstallationI’m trying to install the Ethernet Card, but after I enter the serialnumber, EPSETUP displays an “Unable to locate...serial

Strona 38

After InstallationGreen fight On/Red On ErrorI completed software installation with EPSETUP, but the EthernetCard can’t log into the network (green li

Strona 39 - Restore factory Defaults

Jobs Do not PrintI sent a job to a queue serviced by my the Ethernet Card print server,but it didn’t print, What’s wrong?Check that the Ethernet Cards

Strona 40 - Troubleshooting

Cannot Print to Queue, or Incorrect ResultsI just added a queue to my Ethernet Card using PCONSOLE, but Ican’t print to it. What’s the matter?When you

Strona 41 - 3-2 Troubleshooting

Renaming Print SewerI renamed my Ethernet Card on the master file server usingPCONSOLE, but it still shows up under the old name in EPSETUP?orI reset

Strona 42 - Installation

Answers to Common QuestionsThis section answers some of the most commonly asked questionsabout configuring and using the Ethernet Card.Avoiding Reboot

Strona 43 - After Installation

Installing the Print Server on a Second File ServerHow do I install my Ethernet Card print server on a second file serverwith EPSETUP?EPSETUP is requi

Strona 44 - Jobs Do not Print

5.Create the Ethernet Card print server on the new file server.Select:Print Server Information,Press INSERT,Enter the Ethernet Card print server name.

Strona 45

ContentsIntroductionEthernet Card Hardware...1Ethernet Card Software...2Epson printers serviced by the Ethe

Strona 46 - Renaming Print Sewer

AppendixSpecificationsEnvironmentalOperating temp.:5° to 35°C (41° to 95°F)Storage temp.:0° to 70°C (32° to 158°F)Operating humidity:20% to 80%Network

Strona 47 - Answers to Common

IndexAAnswers to common questions,3-8CCable connection types, 1-3Change printer portconfiguration, 2-3Change queues serviced byprinter, 2-2Configurati

Strona 48

I0Indicator lights, 3-1behavior of, 3-2location of, 3-1Installation, 1-1hardware, 1-1in printer, 1-2software, 1-4Installing on additional fileserversP

Strona 49 - Print Queue Information

Remote printerinstalling as, 1-7Remote printer installationtroubleshooting, 3-3Remote printer mode, 1-6Rename print server, 2-5, 2-11,3-7Report typesc

Strona 50 - Specifications

Caution:Do not use EPSETUP orEPCONFIG while the printer isdisplaying an error message(such as “PAPER SIZE ERROR”).60-0107-001 Rev A

Strona 51 - Index I-1

NoticeBefore connecting this product to your NetWare® v3.12 network, youneed to add the IEEE 802.3 protocol. This step requires you to modifythe serve

Strona 52

2. For all workstations running the utility program forthis product:You need to create (or modify) the NET.CFG file for your workstation.Create (or mo

Strona 53

EPSON®Printed In U.S.A. 94.01-461-104B-001

Strona 54 - Caution:

Chapter 2 Changing the ConfigurationConfiguration Using EPSETUP...2-2Change Queues Serviced by Printer...2-2Change Printe

Strona 55

AppendixIndexvi

Strona 56 - Printed in USA 94.05

Epson’s Ethernet Interface Card for NetWare® is a combination ofhardware and software that lets you connect a laser-type printerdirectly to your Novel

Strona 57 - 61-104B-001

The Ethernet Card software consists of two programs used toinstall and configure the Ethernet Card on the network:Cl EPSETUP is an easy-to-use menu-dr

Komentarze do niniejszej Instrukcji

Brak uwag