Epson 6110i - PowerLite XGA LCD Projector Podręcznik Użytkownika

PowerLite® 6110iMultimedia ProjectorUser’s Guide

10 WelcomeGetting the Most from Your ProjectorDepending on your presentation, you can take advantage of any or all of these options: Connecting to a

100 Solving Problems Make sure your computer’s resolution setting is correct. Ideally, it should be 1024 × 768 to match the projector’s native resolu

Solving Problems 101The image is blurry. There may be dirt or smears on the lens cover glass. Clean the lens cover glass as described on page 86. Ad

102 Solving Problems Adjust the Sharpness setting on the Image menu (see Chapter 4). When you change video settings, you should be able to see the ef

Solving Problems 103The colors of the image are not right. If you’re displaying a computer image, use the Color Mode option in the projector’s Image

104 Solving ProblemsSolving Password Problems You have forgotten the password. Write down the request code that appears in the Password Protect Relea

Solving Problems 105Solving Problems with the Remote ControlThe projector doesn’t respond to remote control commands. If you’re using the remote cont

106 Solving ProblemsWhere To Get HelpInternet SupportVisit Epson’s support website at epson.com/support and select your product for solutions to commo

Solving Problems 107Purchase Supplies and AccessoriesYou can purchase screens, carrying cases, or other accessories from an Epson authorized reseller.

108 Solving Problems

109AProjector InstallationThis appendix provides guidelines on installing the projector in a permanent location, such as a theater or conference room.

Welcome 11Using Your DocumentationYour documentation includes a Quick Setup sheet, warranty brochures, and an Epson® PrivateLine® Support card.The Qui

110 Projector InstallationTo project from overhead, you’ll need the optional ceiling mounting hardware; see page 14 for ordering information. You’ll a

Projector Installation 111Installing the Rear Cable Cover and LockIf you’re mounting the projector on the ceiling, you can install the rear cable cove

112 Projector Installation

113BTechnical SpecificationsGeneralType of display Poly-silicon TFT active matrixSize of LCD panels Diagonal: 0.8 inchResolution(native format) 1024 ×

114 Technical SpecificationsProjection LampType UHE (Ultra High Efficiency)Power consumption 230 WLamp life Up to 4000 hoursPart number V13H010L45Remo

Technical Specifications 115EnvironmentalTemperature Operating: 32 to 104 °F (0 to 40 °C)Storage: 14 to 140 °F (–10 to 60 °C)Humidity Operating: 20 to

116 Technical SpecificationsCompatible Video FormatsThe projector supports NTSC, PAL, and SECAM international video standards, as well as the monitor

Technical Specifications 117*The image is resized using Epson’s SizeWise™ Technology. MAC13MAC16MAC19MAC19MAC216775756075640 × 480*832 × 624*1024 × 76

118 Technical Specifications

119CNoticesThis appendix includes safety instructions and other important information about your PowerLite projector.Important Safety InstructionsFoll

12 WelcomeRegistration and WarrantyYour projector comes with a basic carry-in warranty. For details, see the warranty brochure included with your proj

120 Notices Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified

Notices 121FCC Compliance StatementFor United States UsersThis equipment has been tested and found to comply with the limits for a Class B digital dev

122 Notices

123IndexAA/V Mute, 44, 60, 98Accessories, 14, 107Adjustment Level setting, 62Air filtercleaning, 87high efficient, 14number of hours used, 65ordering,

124 IndexComputercable, 13, 24 to 25connecting to, 24 to 25correcting images, 38selecting source, 32supported display formats, 116 to 117Computer1 Inp

Index 125IiBook, connecting to projector, 24 to 25iMac, connecting to, 24 to 25Imageadjusting, 35 to 38, 54 to 58capturing and saving in projector, 66

126 IndexNNetworkconnecting to, 75managing projector remotely, 73 to 84menu, 63, 76 to 78problems, 104settings, 63, 76 to 78system requirements, 74Net

Index 127Projectoraccessories, 14cleaning, 86connections, see Connecting projectordisabling buttons, 59, 72distance from screen, 16, 113feet, adjustin

128 IndexSourceselecting, 32, 44viewing, 97Speaker, specifications, 113Speakers, connecting, 28Specificationsbrightness, 113dimensions, 114electrical,

Index 129Video Signal setting, 58Volume setting, 59Volume, adjusting, 38, 59WWarning lights, 95 to 97Warranty, 12Web Control Password, 76Weight, 114Wi

Welcome 13Unpacking the ProjectorAfter unpacking the projector, make sure you have all the parts shown below: Save all packaging in case you need to s

14 WelcomeOptional Accessories To enhance your use of the projector, Epson provides the following optional accessories: You can purchase these accesso

151Setting Up the ProjectorThis chapter gives you basic information on setting up the projector: where to position it and how to connect it to a video

16 Setting Up the ProjectorPositioning the ProjectorIf you’re setting up the projector yourself and it isn’t already installed in the classroom or con

Setting Up the Projector 17Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely

18 Setting Up the ProjectorConnecting to Video Equipment You can connect up to four video sources to the projector at the same time. Before starting,

Setting Up the Projector 19Connecting a Composite Video Source1. Locate an RCA-style composite video cable (one may be included with your video equipm

2Important Safety InformationWARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let

20 Setting Up the ProjectorConnecting an S-Video Source1. Locate an S-Video cable (one may have been provided with your video equipment, or you can pu

Setting Up the Projector 21Connecting a Component Video Source1. Locate a component-to-VGA video cable (you can purchase one from Epson; see page 14).

22 Setting Up the ProjectorConnecting an RGB Video SourceFollow these instructions to connect the projector to a video player that has an RGB video ou

Setting Up the Projector 23Connecting Using a BNC-to-VGA Cable1. Locate a BNC-to-VGA video cable (one may be included with your video equipment). 2. C

24 Setting Up the ProjectorConnecting to a Computer You can connect the PowerLite projector to any computer that has a standard video output (monitor)

Setting Up the Projector 25Connecting to the Computer PortFollow these instructions:1. Locate the VGA computer cable provided with the projector.2. Co

26 Setting Up the ProjectorConnecting an External MonitorIf you want to monitor your presentation close-up (on a monitor placed beside the projector)

Setting Up the Projector 27Playing Sound Through the ProjectorYou can play sound through the projector’s speaker system, or you can attach an external

28 Setting Up the ProjectorConnecting External SpeakersTo connect speakers to the projector, follow these steps:1. Obtain the appropriate cable to con

292ProjectingOnce you’ve set up the projector, you’re ready to turn it on, adjust the image, and give your presentation.Although you can operate the p

3ContentsWelcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Getting the Most from Your Projector . . . . . . . . . .

30 ProjectingTurning On Your EquipmentMake sure your projector and other equipment are set up as described in Chapter 1. Then follow the instructions

Projecting 313. Press the orange PPower button on top of the projector—or press the PPower button on the remote control.(If this is your first time us

32 ProjectingSelecting the Image SourceSelecting the image source lets you switch between images input from different pieces of equipment connected to

Projecting 33What To Do If You See a Blank ScreenIf you see a blank screen or a blue screen with the No Signal message, try the following: Make sure

34 ProjectingFrom the Control Panel, open the Display utility. In the Display Properties window, click the Settings tab, then click Advanced. The meth

Projecting 35Adjusting the ImageOnce you see your image, you need to make certain adjustments: To focus or zoom your image, see below. If the i

36 ProjectingAdjusting the Height of Your ImageIf the image is too low on the screen, you can use the front adjustable feet to raise it. 1. Lift the f

Projecting 37Adjusting the Image ShapeIn most cases, you can maintain a square or rectangular image by placing the projector directly in front of the

38 Projecting Or press the Menu button on the remote control, select the Settings menu, and press Enter. From the Settings menu, select Keystone and

Projecting 39Shutting Down the ProjectorWhen you’re finished using the projector, follow the steps below to shut it down. This extends the life of the

42Projecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Turning On Your Equipment . . . . . . . . . . . . . . . . . .

40 Projecting

413Using the Remote ControlThe remote control lets you access your projector’s features from anywhere in the room—up to 33 feet away. For example, you

42 Using the Remote ControlUsing the Remote ControlBefore using the remote, make sure batteries are installed as described on page 43. Then, refer to

Using the Remote Control 43Replacing the Batteries The remote control uses two AAA alkaline batteries. Follow these steps when you need to replace the

44 Using the Remote ControlControlling the Picture and SoundYou can use the remote control to select your picture sources, temporarily turn off the pi

Using the Remote Control 45Stopping ActionYou can use the remote control to stop the action in your video or computer image. Press the Freeze button

46 Using the Remote ControlChanging the Image’s Aspect RatioIf you’re projecting a widescreen format image, you can use the Aspect button on the remot

Using the Remote Control 47Changing the Pointer ShapeFollow the steps below to change the pointer shape.1. Press the Menu button on the remote control

48 Using the Remote ControlSetting the Projector IDThe projector’s default ID is set to Off. This lets it respond to commands from any remote control.

Using the Remote Control 493. While holding the ID button, press a numbered button on the remote control (0 through 9) to select the desired ID. Selec

54Configuring the Projector . . . . . . . . . . . . . . . . . . . 51Using the Menu System. . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Res

50 Using the Remote Control

514Configuring the Projector You can use the projector’s on-screen menus to adjust the image, sound, and other features. This chapter covers the follo

52 Configuring the ProjectorUsing the Menu SystemYou can use the remote control (or the projector’s control panel) to access the menu system and chang

Configuring the Projector 534. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may

54 Configuring the ProjectorAdjusting Colors and ClarityThe Image menu lets you make adjustments to the colors of the projected image and fine-tune br

Configuring the Projector 55sRGB: For projecting standard sRGB computer displays.Blackboard: Fixed color mode for projecting against a green blackboar

56 Configuring the ProjectorAdjusting the Input Signal1. Press the Menu button on the remote control, highlight Signal, then press the Enter button to

Configuring the Projector 572. Use the pointer button to highlight menu items, then press the Enter button to select from any of the following option

58 Configuring the Projector Video Signal (composite and S-Video)Leave this setting at Auto unless you are using a 60-Hz PAL system (select PAL60).

Configuring the Projector 59 Operation LockIn Full Lock mode, disables all of the projector’s buttons, including the P Power button. In Partial Lock

66Maintaining the Projector. . . . . . . . . . . . . . . . . . . 85Cleaning the Lens Cover Glass . . . . . . . . . . . . . . . . . . . . . . . 86Clean

60 Configuring the ProjectorSelecting Projector Setup OptionsUse the Extended menu to customize the way you set up the projector. You can configure th

Configuring the Projector 61 User’s LogoTurn this setting On to display the image or logo you have captured whenever the projector is turned on. See

62 Configuring the Projector Air Filter SettingAlarm Timer: Lets you turn the air filter replacement notification on or off. If you are using the smo

Configuring the Projector 63 LanguageLets you select the language to be used for the projector menus.3. When you’re finished, press Esc or Menu.Selec

64 Configuring the ProjectorViewing Lamp Usage and Other InformationUse the Info menu to view information about the display settings of your computer

Configuring the Projector 65 Air FilterDisplays type of air filter and the number of hours it has been used. SourceDisplays the input source current

66 Configuring the ProjectorIf you assign the projector a password, a screen appears requesting the password whenever the projector is turned on. If y

Configuring the Projector 673. Use the pointer button to highlight User’s Logo, then press the Enter button.4. When you see the message Choose this i

68 Configuring the Projector7. When you see this screen, select a zoom rate (display size), and press Enter.8. When you see the message Save this imag

Configuring the Projector 698. To display your screen logo when the A/V Mute button is pressed, select A/V Mute and press Enter.9. Select Logo and pre

7CNotices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Important Safety Instructions. . . . . . . . . . . . . . . . .

70 Configuring the ProjectorProtecting Projector SettingsYou can password protect the User’s Logo and Network settings to prevent them from being chan

Configuring the Projector 71Turning On Password ProtectionIf you enable the Power On Protect setting, a screen appears requesting the password wheneve

72 Configuring the ProjectorStarting the Projector with a PasswordWhen the password function is enabled, you see a password entry screen when you turn

735Monitoring the Projector Over a NetworkThe software included with your projector lets you control your projector(s) over a network. Use EMP Monito

74 Monitoring the Projector Over a NetworkInstalling the Network SoftwareThe projector software CD-ROM includes EMP Monitor for monitoring your projec

Monitoring the Projector Over a Network 75Connecting to the NetworkFollow these steps to connect the projector to your network and configure it with a

76 Monitoring the Projector Over a NetworkSelecting Network SettingsFollow the instructions in this section to set up the projector’s network settings

Monitoring the Projector Over a Network 77 SNMPIf you’re a network administrator, you can use the SNMP option to enter a Trap IP Address. This lets y

78 Monitoring the Projector Over a Network Address 1/2/3 SettingChoose one of the Address Setting fields, then enter the e-mail address where you wan

Monitoring the Projector Over a Network 79If you’ve added the program to the Startup programs folder, it may already be open. If so, click the icon in

8

80 Monitoring the Projector Over a NetworkMonitoring Your ProjectorsThe EMP Monitor screen lets you monitor your projector(s) status and check if a pr

Monitoring the Projector Over a Network 81Power status iconsThe projector is powered on and its status is normal.The projector is powered off and its

82 Monitoring the Projector Over a NetworkUsing E-mail AlertsYou can set up e-mail alerts to warn you of problems with the projector.1. Open EMP Monit

Monitoring the Projector Over a Network 838. When you’re done, click the OK button.If a projector experiences a problem, EMP Monitor sends an e-mail m

84 Monitoring the Projector Over a Network5. Select one of the menu options, then change any of the settings as needed. These settings correspond to t

856Maintaining the ProjectorYour projector needs little maintenance. All you have to do on a regular basis is keep the lens cover glass clean. Any dir

86 Maintaining the ProjectorCleaning the Lens Cover GlassClean the lens cover glass whenever you notice dirt or dust on the surface. Use a canister o

Maintaining the Projector 87Cleaning the Air FilterClean the air filter when you see any of the following messages: The air filter is clogged. Clean o

88 Maintaining the ProjectorFollow these steps:1. Turn off the projector and unplug the power cord.2. Remove the air filter by lifting up on the two t

Maintaining the Projector 89Replacing the Lamp The projection lamp typically lasts about 4000 hours. It is time to replace the lamp when: The projec

9-WelcomeThe PowerLite® 6110i is a versatile projector designed to ensure that your presentations are easy and trouble-free, whether you use it in the

90 Maintaining the Projector5. Loosen the two screws holding the lamp in place (you can’t remove them). 6. Pull the lamp straight out.7. Gently insert

Maintaining the Projector 91Resetting the Lamp TimerAfter you replace the lamp, you need to reset the lamp timer using the projector’s menu. 1. Plug t

92 Maintaining the Projector

937Solving ProblemsThis chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t so

94 Solving ProblemsUsing On-Screen HelpIf the image doesn’t look right or your audio isn’t working, you can get help by pressing the blue ? Help butto

Solving Problems 95If none of the suggestions solves your problem, see additional solutions to problems in the following sections.Checking Projector S

96 Solving ProblemsGreen Flashing orangeIt’s time to replace the lamp. See page 89 for instructions. If you continue to use the lamp after the replace

Solving Problems 97Viewing Lamp Usage and Other InformationUse the Info menu to view information about the image source, the display settings of your

98 Solving ProblemsSolving Problems with the Image or SoundThe Power light does not come on.Make sure the power cord is connected securely both at t

Solving Problems 99If you’re using a PC notebook: Hold down the Fn key on the keyboard and press the function key that lets you display on an externa